Firmware Updates

Installation Instructions

• Download the latest version of the AmpPRO PC Application. It is VERY important that you use the latest version.
• Download the latest version of our firmware.
• Extract the firmware file and setup file from the .ZIP files that were just downloaded.
• Connect the interface to the computer's USB port and install the update.

Detailed Instructions

1. If this is the first time using the AmpPRO PC Application, run and install “amppro_setup.exe”. This will install the PC Application onto the computer. The AmpPRO program will then install the update files from the computer to the interface.
2. Open the AmpPRO PC Application using the new shortcut created on your desktop.
3. Connect the interface to the computer using a standard to micro USB cable.
4. Click the "Firmware" icon.
5. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
6. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

Installation Instructions

• Download the latest version of the AmpPRO PC Application. It is VERY important that you use the latest version.
• Download the latest version of our firmware.
• Extract the firmware file and setup file from the .ZIP files that were just downloaded.
• Connect the interface to the computer's USB port and install the update.

Detailed Instructions

1. If this is the first time using the AmpPROPC Application, run and install “ampproexe”. This will install the PC Application onto the computer. The AmpPRO program will then install the update files from the computer to the interface.
2. Open the AmpPROPC Application using the new shortcut created on your desktop.
3. Connect the interface to the computer using a standard to micro USB
4. Click the "Firmware" icon.
5. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
6. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

Installation Instructions

• Download the latest version of the AmpPRO PC Application. It is VERY important that you use the latest version.
• Download the latest version of our firmware.
• Extract the firmware file and setup file from the .ZIP files that were just downloaded.
• Connect the interface to the computer's USB port and install the update.

Detailed Instructions

1. If this is the first time using the AmpPROPC Application, run and install “ampproexe”. This will install the PC Application onto the computer. The AmpPRO program will then install the update files from the computer to the interface.
2. Open the AmpPROPC Application using the new shortcut created on your desktop.
3. Connect the interface to the computer using a standard to micro USB
4. Click the "Firmware" icon.
5. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
6. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

Installation Instructions

• Download the latest version of the AmpPRO PC Application. It is VERY important that you use the latest version.
• Download the latest version of our firmware.
• Extract the firmware file and setup file from the .ZIP files that were just downloaded.
• Connect the interface to the computer's USB port and install the update.

Detailed Instructions

1. If this is the first time using the AmpPROPC Application, run and install “ampproexe”. This will install the PC Application onto the computer. The AmpPRO program will then install the update files from the computer to the interface.
2. Open the AmpPROPC Application using the new shortcut created on your desktop.
3. Connect the interface to the computer using a standard to micro USB
4. Click the "Firmware" icon.
5. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
6. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

Installation Instructions

• Download the latest version of the AmpPRO PC Application. It is VERY important that you use the latest version.
• Download the latest version of our firmware.
• Extract the firmware file and setup file from the .ZIP files that were just downloaded.
• Connect the interface to the computer's USB port and install the update.

Detailed Instructions

1. If this is the first time using the AmpPROPC Application, run and install “ampproexe”. This will install the PC Application onto the computer. The AmpPRO program will then install the update files from the computer to the interface.
2. Open the AmpPROPC Application using the new shortcut created on your desktop.
3. Connect the interface to the computer using a standard to micro USB
4. Click the "Firmware" icon.
5. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
6. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

Installation Instructions

• Download the latest version of the AmpPRO PC Application. It is VERY important that you use the latest version.
• Download the latest version of our firmware.
• Extract the firmware file and setup file from the .ZIP files that were just downloaded.
• Connect the interface to the computer's USB port and install the update.

Detailed Instructions

1. If this is the first time using the AmpPRO PC Application, run and install “amppro_setup.exe”. This will install the PC Application onto the computer. The AmpPRO program will then install the update files from the computer to the interface.
2. Open the AmpPRO PC Application using the new shortcut created on your desktop.
3. Connect the interface to the computer using a standard to micro USB cable.
4. Click the "Firmware" icon.
5. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
6. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

1. If this is the first time using the BCI PC Application, download “BCI PC Application".
2. Download the firmware file.
3. Extract the BCI PC Application file, then run the installer. This will install the PC Application onto the computer.
4. Open the BCI PC Application using the new shortcut created on your desktop.
5. Connect the interface to the computer using a standard to micro USB cable.
6. Click the "Firmware" icon.
7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

1. If this is the first time using the BCI PC Application, download “BCI PC Application".
2. Download the firmware file.
3. Extract the BCI PC Application file, then run the installer. This will install the PC Application onto the computer.
4. Open the BCI PC Application using the new shortcut created on your desktop.
5. Connect the interface to the computer using a standard to micro USB cable.
6. Click the "Firmware" icon.
7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

INSTALLATION INSTRUCTIONS

1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
2. Download the firmware file.
3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Set all four DIP Switches to ON (DOWN) position.
6. Connect the interface to the computer using a standard to micro USB cable.
7. Click the "Firmware" icon.
8. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
9. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

INSTALLATION INSTRUCTIONS

1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
2. Download the firmware file.
3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Connect the interface to the computer using a standard to micro USB cable.
6. Click the "Firmware" icon.
7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

INSTALLATION INSTRUCTIONS

1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
2. Download the firmware file.
3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Connect the interface to the computer using a standard to micro USB cable.
6. Click the "Firmware" icon.
7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

INSTALLATION INSTRUCTIONS

1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
2. Download the firmware file.
3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Connect the interface to the computer using a standard to micro USB cable.
6. Click the "Firmware" icon.
7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

INSTALLATION INSTRUCTIONS

1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
2. Download the firmware file.
3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Connect the interface to the computer using a standard to micro USB cable.
6. Click the "Firmware" icon.
7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

INSTALLATION INSTRUCTIONS

1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
2. Download the firmware file.
3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Connect the interface to the computer using a standard to micro USB cable.
6. Click the "Firmware" icon.
7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

***THESE INSTRUCTIONS APPLY TO SQUARE MODULES ONLY! IF YOU HAVE A RECTANGULAR MODULE THEN THERE ARE NO FIRMWARE UPDATES AT THIS TIME.***

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Important Information

Vista & 7 64-bit Users - we have received compatibility reports from users operating under the Vista & 7 64-bit OS. No such problems have been reported with Vista or 7 32-bit OS. Please use Vista or 7 32-bit when updating drivers.

Requirements Before You Begin

1. PC or Laptop running Windows XP, Vista or 7 (32 bit ONLY) **NOT compatible with any other operating systems
2. Administrative rights on the Windows computer - This is required for installing the USB driver pack and updating software
3. Standard to 5-Pin mini USB cable
4. Disable any Pop-up blockers you have enabled on your browser.
   

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Installation Instructions

• Save the .zip file to your desktop.
• Once saved to your desktop, right click the .zip file and choose "Extract All".
• Follow the instructions included in the .zip file to update your iSimple Connect.

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

Gateway Firmware Updater

The Gateway Firmware Updater will download the most recent firmware directly from iSimple. Ensuring you have the most up-to-date firmware with the most advanced features! A user manual is provided.

• Download and install the latest version of the Gateway Update Software.
• The program will walk you through step-by-step to upgrade your Gatway (internet connection is required for update)
• NOTE: once installed the updater will download the most recent FIRMWARE from our servers
• NOTE: The Firmware version may be different from the Gateway Updater version. You will see the most recent Firmware versions in the Gateway Updater Program once a connection to our server is made.

Gateway Firmware Updater

• Download the update package to your PC. Make sure you save it in a place you can easily find it like a "New Folder" on your desktop.
• Extract the files from the .zip folder to your PC. Save them in the same place as the .zip folder.
• Follow the procedure outlined in this video to setup the program and update your module: https://aampglobal.zendesk.com/hc/en-us/articles/360043247391

***THESE INSTRUCTIONS APPLY TO BLUE MODULES ONLY! IF YOU HAVE A BLACK MODULE THEN THERE ARE NO FIRMWARE UPDATES AT THIS TIME.***

INSTALLATION INSTRUCTIONS

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

DETAILED INSTRUCTIONS

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the Interface. This can be found in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

***THESE INSTRUCTIONS APPLY TO BLUE MODULES ONLY! IF YOU HAVE A BLACK MODULE THEN THERE ARE NO FIRMWARE UPDATES AT THIS TIME.***

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Notes

• If not updated, download and install the PAC-UP firmware.
• Download and install the latest version of our database.
• Connect the PAC-UP to the computer's USB port and PP-SWI's data port, and install the update.

Detailed Instructions

• If this is the first time updating you PP-SWI, download, run and install the "PAC Interface Updater". This will install "Interface Updater" onto the computer. The "Interface Updater" will update the files from the computer to PP-SWI.
• Download and extract the "PP-SWI Database r--.zip" file. Please remember the location that the .suf file is extracted to. We will need this for step 7.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to PP-SWI.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Click "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, reconnect PAC-UP to the computer and restart the software.
• Select "PP-SWI" from "Interface select" pull down menu.
• Click "Update Database". Locate the new database file you extracted in step 2 and select it.
• Once the file is chosen the update will begin. When successful it will show the text "End Update". It is now safe to disconnect the PP-SWI / PAC-UP from the computer.

Installation Instructions

If not updated, download and install the latest version of the PAC-UP firmware. It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, run and install "Interface Updater Setup". This will install "Interface Updater" onto the computer. The "Interface Updater" will update the files from the computer to RP Interface.
• Download the file
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Click "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, reconnect PAC-UP to the computer and restart the software.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second and third digit of the revision number on your module matches the second and third digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

If not updated, download and install the latest version of the PAC-UP firmware. It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, run and install "Interface Updater Setup". This will install "Interface Updater" onto the computer. The "Interface Updater" will update the files from the computer to RP Interface.
• Download the file
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Click "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, reconnect PAC-UP to the computer and restart the software.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second and third digit of the revision number on your module matches the second and third digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

If not updated, download and install the latest version of the PAC-UP firmware. It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, run and install "Interface Updater Setup". This will install "Interface Updater" onto the computer. The "Interface Updater" will update the files from the computer to RP Interface.
• Download the file
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Click "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, reconnect PAC-UP to the computer and restart the software.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second and third digit of the revision number on your module matches the second and third digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

INSTALLATION INSTRUCTIONS

1. If this is the first time using the RadioPRO PC Application, download “radiopro_setup.zip”.
2. Download the firmware file.
3. Extract the Radio PRO PC Application file, then run the installer. This will install the PC Application onto the computer.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Connect the interface to the computer using a standard to micro USB cable.
6. Click the "Firmware" icon.
7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

INSTALLATION INSTRUCTIONS

1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
2. Download the firmware file.
3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Connect the interface to the computer using a standard to micro USB cable.
6. Click the "Firmware" icon.
7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

INSTALLATION INSTRUCTIONS

1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
2. Download the firmware file.
3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Connect the interface to the computer using a standard to micro USB cable.
6. Click the "Firmware" icon.
7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

INSTALLATION INSTRUCTIONS

1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
2. Download the firmware file.
3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Connect the interface to the computer using a standard to micro USB cable.
6. Click the "Firmware" icon.
7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

1. INSTALLATION INSTRUCTIONS

   1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
   2. Download the firmware file.
   3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
   4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
   5. Connect the interface to the computer using a standard to micro USB cable.
   6. Click the "Firmware" icon.
   7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
   8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

INSTALLATION INSTRUCTIONS

1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
2. Download the firmware file.
3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Set all four DIP Switches to ON (DOWN) position.
6. Connect the interface to the computer using a standard to micro USB cable.
7. Click the "Firmware" icon.
8. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
9. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

***These instructions apply to blue modules only! If you have a black module then there are no firmware updates at this time.***

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

***THESE INSTRUCTIONS APPLY TO BLUE MODULES ONLY! IF YOU HAVE A BLACK MODULE THEN THERE ARE NO FIRMWARE UPDATES AT THIS TIME.***

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

***THESE INSTRUCTIONS APPLY TO BLUE MODULES ONLY! IF YOU HAVE A BLACK MODULE THEN THERE ARE NO FIRMWARE UPDATES AT THIS TIME.***

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

INSTALLATION INSTRUCTIONS

1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
2. Download the firmware file.
3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Connect the interface to the computer using a standard to micro USB cable.
6. Click the "Firmware" icon.
7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

INSTALLATION INSTRUCTIONS

1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
2. Download the firmware file.
3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Connect the interface to the computer using a standard to micro USB cable.
6. Click the "Firmware" icon.
7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

Installation Instructions

It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software. 

Detailed Instructions

• If this is the first time, download and install "PAC-UP Interface Updater". This will install the necessary software to update the firmware on the RP Interface. This can be found at in the "Download" tab at the very bottom of the firmware list on this page.
• Download the firmware file to a location on your computer that you can easily find.
• Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
• Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
• Click the "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, disconnect the PAC-UP from the computer, restart the software, then reconnect the PAC-UP and try again.
• Select your RP Interface from the "Interface select" pull down menu.
• Click "Update firmware". The new firmware can be found where you saved it before beginning.
• Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second from last digit of the revision number on your module matches the second from last digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

INSTALLATION INSTRUCTIONS

1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
2. Download the firmware file.
3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Set all four DIP Switches to ON (DOWN) position.
6. Connect the interface to the computer using a standard to micro USB cable.
7. Click the "Firmware" icon.
8. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
9. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".

1. If this is the first time using the RadioPRO PC Application, download the Radio PRO PC Application. This can be found at the "Download" tab at the very bottom of the firmware list on this page.
2. Download the firmware file.
3. Install the Radio PRO PC Application using the .exe file you downloaded in step one.
4. Open the RadioPRO PC Application using the new shortcut created on your desktop.
5. Connect the interface to the computer using a standard to micro USB cable.
6. Click the "Firmware" icon.
7. Click “Select File” and browse to the new firmware file. The new firmware can be found where you saved it before beginning.
8. Once the file is chosen the update will begin. When successful it will show the text "Update Completed".