• Radio Replacement

RadioPRO Radio Replacement Interface with Built-In OnStar Retention, Pre- Programmed SW Control Retention and Navigation Outputs

RP5-GM31

RadioPRO Radio Replacement Interface with Built-In OnStar Retention, Pre- Programmed SW Control Retention and Navigation Outputs

$279.95

RP5-GM31

New product

LAN 29

RadioPRO Radio Replacement Interface with Built-In OnStar Retention, Pre- Programmed SW Control Retention and Navigation Outputs View larger
An all in one radio replacement and SWC interface, the innovative new RadioPRO5 comes pre-loaded with OnStar retention, amplifier retention, SWC software, navigation based output signals and other features that save time and money during installation.

Product Features
  • Retains OnStarĀ® and functions when the factory radio is replaced
  • Retains steering wheel controls (pre-programmed)
  • Retains Factory Bluetooth (2009+ model vehicles)
  • Retains rear seat audio controls
  • Retains factory satellite radio with text displayed in the Driver Information Center (cluster display)
  • Retains all warning chimes (chime module included)
  • Retains back-up sensors/park assist and back-up camera signal
  • Retains factory Bose and premium Bose audio systems (Y91 digital system does not support fading from aftermarket radio)
  • Compatible with non-amplified audio systems
  • Dual zone function
  • Chime volume adjustment
  • Rear seat audio and video (GMRVD) required
  • Retained accessory power output (RAP)
  • Reverse wire output
  • VSS (Vehicle Speed Sense) output
  • Illumination output and parking brake output
  • Includes antenna adaptor
  • Retains lane departure warning system





Compatibility Notes
  • 2012+ GM trucks and SUVs equipped with factory navigation radios require the RP5-GM32
  • 2014+ Silverado and Sierra: Only compatible with 2500 & 3500 series trucks with non-navigation radios. 1500 series must use the RP5-GM51. 2500 & 3500 series trucks with navigation radios must use the RP5-GM32
  • In Premium Amplified Systems there will be no fading capability of the aftermarket stereo.
  • Chevrolet Express vans & GMC Savannah vans equipped with diesel engines are not compatible
  • In order to retain the factory XM tuner the aftermarket head unit MUST be equipped with an auxiliary input
  • In order to retain the factory XM tuner the vehicle must be equipped with steering wheel controls and a driver information center
  • Sony Bluetooth SWC commands are only supported with revision 1.6.6.14 or higher
  • Does not retain escalating tones of parking sensor proximity

Check for the latest firmware



Patent # 8,014,540 & 8,184,825

RP5-GM31 Instruction Manual
 Download (1.25M)
Accessory Power Tech Bulletin
 Download (1.72M)
Year(s) Make Model Trim Level Additional Info
2008-2017 BUICK ENCLAVE ALL TRIM LEVELS
2006-2011 BUICK LUCERNE ALL TRIM LEVELS
2006-2010 CADILLAC DTS ALL TRIM LEVELS
2007-2014 CADILLAC ESCALADE ALL TRIM LEVELS
2007-2014 CADILLAC ESCALADE ESV ALL TRIM LEVELS
2007-2014 CADILLAC ESCALADE EXT ALL TRIM LEVELS
2007-2009 CADILLAC SRX ALL TRIM LEVELS
2007-2013 CHEVROLET AVALANCHE ALL TRIM LEVELS
2007-2009 CHEVROLET EQUINOX ALL TRIM LEVELS
2008-2016 CHEVROLET EXPRESS VAN ALL TRIM LEVELS
2006-2013,2015 CHEVROLET IMPALA ALL TRIM LEVELS
2014,2016 CHEVROLET IMPALA CLASSIC
2006-2007 CHEVROLET MONTE CARLO ALL TRIM LEVELS
2007-2014 CHEVROLET SILVERADO ALL TRIM LEVELS
2014 CHEVROLET SILVERADO HD ALL TRIM LEVELS
2007-2014 CHEVROLET SUBURBAN ALL TRIM LEVELS
2007-2014 CHEVROLET TAHOE ALL TRIM LEVELS
2009-2017 CHEVROLET TRAVERSE ALL TRIM LEVELS
2007-2016 GMC ACADIA ALL TRIM LEVELS
2017 GMC ACADIA CLASSIC
2008-2017 GMC SAVANA ALL TRIM LEVELS
2007-2014 GMC SIERRA ALL TRIM LEVELS
2007-2014 GMC SIERRA HD ALL TRIM LEVELS
2007-2014 GMC YUKON ALL TRIM LEVELS
2008-2009 HUMMER H2 ALL TRIM LEVELS
2007-2009 PONTIAC TORRENT ALL TRIM LEVELS
2007-2010 SATURN OUTLOOK ALL TRIM LEVELS
2008-2010 SATURN VUE ALL TRIM LEVELS
2007-2008 SUZUKI XL-7 ALL TRIM LEVELS

RP5-GM31

RadioPRO Radio Replacement Interface with Built-In OnStar Retention, Pre- Programmed SW Control Retention and Navigation Outputs

Installation Instructions

If not updated, download and install the latest version of the PAC-UP firmware. It is VERY important that you use the latest version of Interface Updater. Not doing so may damage the interfaces software.Ā 

Detailed Instructions

  • If this is the first time, run and install "Interface Updater Setup". This will install "Interface Updater" onto the computer. The "Interface Updater" will update the files from the computer to RP Interface.
  • Download the file
  • Connect the PAC-UP to the computer using supplied USB cable. Connect the PAC-UP to the RP Interface.
  • Open the Interface Updater Program by going to Start >All Programs >AAMP of America > Interface Updater.
  • Click "Connect" button to establish connection between the PAC-UP and the computer. The "Connected" check box will be checked if successful. If unsuccessful, reconnect PAC-UP to the computer and restart the software.
  • Select your RP Interface from the "Interface select" pull down menu.
  • Click "Update firmware". The new firmware can be found where you saved it before beginning.
  • Once the files are chosen the update will begin. When successful it will show the text "End Update".

IMPORTANT: It is very important that the second and third digit of the revision number on your module matches the second and third digit of the new firmware file revision number. If your numbers do not match, please contact our tech support department.

  • Firmware Download, Version 1.6.6.17 (Released on June 1st, 2016)
    Release Notes
    • Fixed Aftermarket mode for SWC programming
    Download
  • Firmware Download, Version 1.6.6.16 (Released on February 13th, 2015)
    Release Notes
    • Separates Sony & Pioneer
    • Adds Alpine VR command
    • Fixes LED problem when using SWC
    Download
  • Firmware Download, Version 1.4.4a.4m (Released on April 17th, 2013)
    Release Notes
    • Fixes issues seen with interface shutting down every 10 minutes due to OnStar update
    • Fixes issues seen with SWC when used with new Alpine & JVC head units
    • Adds new Kenwood Bluetooth function support for SWC
    Download
  • Firmware Download, Version 1.4.4c (Released on January 30th, 2013)
    Release Notes
    • Fixes issues seen with SWC when vehicle is moving
    Download
  • Firmware Download, Version 1.4.4 (Released on December 18th, 2012)
    Release Notes
    • Improves chime tone and reliability of default SWC programming
    Download
  • Firmware Download, Version 1.4.3g (Released on November 30th, 2012)
    Release Notes
    • Initial release
    Download
  • Utility/Other, Version 2.6 (Released on July 21st, 2017)
    Release Notes
    PAC-UP Interface Updater
    Download